e85 Conversion Kits

Save Money

Drive E85

Calculate Savings

Live e85 Fuel Prices

e85 Stations Locations - I

e85 Stations Locations - II

e85 Stations Locations - III

Ethanol: Rumor vs Reality

Benefit with ETOM

USA e85 Conversion Kit

Gasoline Savings & Mileage

Safe

Why should I purchase the EToM conversion over unit X?

Ordering is as easy as choosing your car, and the EToM conversion is just as easy to install. Unlike other kits, there are no hidden extras to purchase to get convert your vehicle and no complicated preparation to start running e85 fuel. EToM is far superior by saving you real and noticeable money at the pumps. You also benefit from running a fuel that is good for the environment and your wallet.

What if I sell my vehicle?

The EToM unit can be removed just as easily as it was installed. The greatest part of the EToM conversion kit is each connection can be unplugged in seconds and there are no wires that ever need to be spiced into.

Does the EToM replace the factor vehicles computer?

No. The EToM conversion kit utilizes a standalone computer system to work along side your original computer. This allows the vehicles computer to adjust to the E85 tuning.

What are the terms of the EToM Warranty?

Ethanol Technology of Minnesota, LLC. warrants the EToM unit to be free from defects in materials and workmanship for a period of 1 year as measured from the date of purchase. Ethanol Technology of Minnesota, LLC shall, in its sole discretion, repair or replace any defective components returned to Ethanol Technology of Minnesota, LLC during the warranty period. All warranty returns must be accompanied by the original sales receipt.

Any damage due to misuse, tampering, improper installation, accident, exposure to weather, chemicals or corrosives, or any service by a non-authorized party, completely and irrevocably voids this warranty.

The e85 conversion kit contains:

1. ETOM 'Black Box' measuring 2" x 3" x 5" containing the microprocessors for the fuel injectors and oxygen sensors
2. The fuel injector jumper harness
3. The oxygen sensor jumper harness
4. The On/Off toggle switch
5. The install kit with zip ties and velcro

The wiring harness's and processor box are all one piece. Pass the switch through the firewall and your ready to go.

How do I install the EToM system?

The system comes assembled. There are not any wires to cut and splice or any programming to do. The following steps allow you to install your ETOM system in your vehicle:

1. Unclip the fuel injector wires from your fuel injectors and install the ETOM injector harness in between the vehicles injectors and wiring harness. These are male/female and can only be hooked up one way. The harness ends are marked with a yellow tag marked "Injector" It does not matter what order they are hooked up.

2. Unclip the front/upstream oxygen sensor/sensors wire and install the ETOM oxygen sensor/sensors harness between the oxygen sensor and the vehicles wiring harness. These are also male/female and can only be hooked up one way. The oxygen sensor harness end/ends have a bright green tag on them and are labeled "oxygen sensor". Vehicles can have one or two oxygen sensors. The ETOM system for each vehicle will come with the correct number of oxygen sensor leads.

3. The on/off switch can either be installed under the hood or inside the cab of the vehicle. To install the switch inside the cab pass the wire ends marked "Switch" either through an existing hole in the fire wall or drill a small hole in the fire wall. The switch wires have a bright blue label on them. Plug the switch into the wires. The wire and the switch are male/female and can only be installed one way. For either under hood or inside the cab use the supplied alcohol wipe to clean an area for the supplied velcro strip. After the alcohol has dried apply the strip of velcro to the desired switch location. Now apply the switch to the velcro.

4. Install the Microswitch box to the firewall, a fender or any other flat spot in the engine bay. Use the supplied self tapping screws, zip ties or the velcro strip. If using the velcro strip make sure the surface is cleaned with the supplied alcohol wipe before attaching the strip to the surface.

5. Use the supplied zip ties to make sure that all the wires from the micro switch box, injector harness, oxygen sensor harness and switch do not interfere with any mechanical movement in the engine compartment and that the wires are pulled away from the exhaust or any other hot surface.

6. Turn the ignition key to on and and flip the ETOM switch to ON. The indicator will glow green when the system is on. When the system is off the ETOM automatically reverts to the vehicles original gas programming.The ETOM system will only activate when the key is in the ON position.

How much does it cost to have EToM installed?

We have installed this kit including running the switch through the firewall in less then 30 minutes in most vehicles. Each model of vehicle is different and some vehicles may take longer then others.

A professional installation for most vehicles should take no longer then one hour of time.